Ariens Sno Tek 24 User Manual
- Ariens Sno Tek 24 Manual
- Ariens Sno-tek 24 Owner's Manual
- Ariens Sno Tek 24 Manual
- Ariens Sno Tek 20 Manual
- Ariens Snow Tek 24 Manual
GB - 22
- Ariens Company 655 West Ryan Street Brillion, WI 920-756-2141 www.ariens.com Sno-Tek Cover Waterproof, washable and tear-resistant, this cover protects your Sno-Tek when it is not in use. Non-Abrasive Skid Shoes Protect the decorative surfaces around your home.
- Ariens sno-tek 920401 User Manual. Sno-Tek ™ Two-Year Limited. Ariens Company (Ariens) warrants to the original purchaser that Sno-Tek brand products will be free from defects in material and workmanship for a period of two years after the date of purchase. An authorized Ariens dealer will repair any.
4. Remove spring pin from chute crank and
Find the user manual you need for your lawn and garden product and more at ManualsOnline. 920401 – Sno-Tek 26. Model 932105. Need an owners manual. Looking for a manual for a Spirt Snow thrower, wit. I was given a # 932040 ariens snow blower.I can't. Sponsored Listings. Loading Products. About Us; Our Community.
separate.
5. Remove belt finger by removing cap
screws mounting belt finger to engine
(Figure 19 or 20).
6. Remove attachment drive belt from
engine sheave (it may be necessary to
turn engine sheave using recoil starter
handle).
IMPORTANT:
To avoid bending bottom cover,
when tipping unit apart, support handlebars
firmly or tip unit up on housing and remove
bottom cover by removing six cap screws
before separating unit.
7. Support the frame and housing.
8. Remove hex bolts securing housing to
frame (two on each side). Tip housing
and frame apart on pivot pin.
9. Remove attachment drive belt from
attachment pulley (hold brake away from
belt).
Replace Attachment Drive Belt
1. Place new belt onto attachment pulley.
NOTE:
Holding down the attachment clutch
lever will make it easier to reconnect the
housing and frame.
2. Tip housing and frame back together
and secure with hex bolts.
3. Place belt onto engine sheave.
4. Replace belt finger.
IMPORTANT:
With the clutch lever engaged,
the belt finger located opposite the belt idler
must be less than 1/8 in. (3,2 mm) from the
belt, but not touching the belt, or belt
grabbing may occur causing impeller to rotate
while the attachment clutch is disengaged
(Figure 20).
5. Adjust clutch perAttachment
Clutch/Brake Adjustment on page 24.
6. Replace chute crank and secure with
spring pin.
7. Run in the attachment belt. See Run-in
8. Replace belt cover and tighten
hardware.
This edition obsoletes all previous revisions. Dell compellent series 40 user manual. .Storage Center ™ Enterprise Manager 5.Enterprise Manager 5.5 Installation and Setup Guide 680-028-010 Revision Date Description A March 2011 Initial release. B April 2011 Updated to include new locations for contacting Dell technical support, downloading product manuals, as well as miscellaneous corrections.
CAUTION:
Always support the unit
frame and housing when loosening
the cap screws holding them
together. Never loosen cap screws
while unit is in service position.
Figure 18
OS8062
1. Pinion Gear
2. Belt Cover Champion 2000 juicer.
3. Spring Pin
4. Chute Crank
WARNING:
AVOID INJURY. Auger
must stop within 5 seconds when
attachment lever is released or
serious injury or unit damage may
result.
Figure 19
OS8160
5
3
2
1
4
1. Traction Belt
Idler
2. Traction Drive
Belt
3. Engine Sheave
4. Belt Finger
5. Attachment
Drive Belt
6. Attachment
Pulley
7. Attachment
Idler Nut
8. Attachment
Belt Idler
8